GIMAN
Superbolt · mechanical tensioners

Tension you can trust,
with a hand wrench.

Multi-jackbolt tensioners replace the hex nut on the joints that cannot leak. No hammer wrench, no hydraulic torque, no hot work.

Offshore platformsBlowout preventersGas & steam turbinesWind
How it works

Many small bolts do the job of one huge bolt

A Superbolt tensioner threads onto the existing stud in place of the hex nut. Instead of turning one large nut against friction, you tighten a ring of small jackbolts.

  1. Spin it on by handA direct replacement for the hex nut, on the stud you already have.
  2. Tighten the jackboltsEach one needs little torque. Together they push against a hardened washer.
  3. The stud is in pure tensionNo torsion and no thread galling. The load is even around the whole bolt circle.
  4. Take it off the same wayHand tools only, outage after outage. The tensioner is reusable.
Animation: assembly and tightening

Hammer wrench or hydraulic torque

  • About 90% of the torque is lost to friction
  • Preload error of ±30–40% or more
  • Compressor, pump, hoses and wrench: each one can fail
  • Three people, heavy gear, impact injuries
  • Leaks and re-tightening at start-up

Superbolt

  • Pure tension on the stud
  • Preload accuracy of ±5–10%
  • One hand torque wrench
  • One person, in confined spaces
  • Leak-tight from the first pass

Torque is not tension. Tension is what seals the joint.

PEMEX offshore

Where we started: compression modules in the Bay of Campeche

In June 2018 we surveyed the assembly and start-up of a high-pressure compression module at the POL-A process centre. Flanges from 2 to 36 inches were bolted at night, in tight spaces, with hammer wrenches and hydraulic torque. Every leak at start-up meant re-tightening and deferred production.

Before: a full crew on one hammer wrench
Before: hydraulic torque — pump, hoses and wrench

The trial: Superbolt goes on and comes off with a hand wrench

Superbolt: tightening with a hand wrench
Superbolt: loosening with the same hand wrench
77%less time removing and fitting studs on a 24-inch, class 150 flange
0 hof leak re-tightening. The previous method needed 10 hours and three re-tightenings
3 → 1people needed to tighten the joint

Our own measurements on the platform, against hydraulic torque on the same flange.

Abkatún-A, December 2019

We installed Superbolt on the compression-module joints with our own crew on board and a torque audit of every tensioner.

JointSize
Flanging module36" · 600#
V-101 manway30" · 300#
V-101 inlet and outlet24" · 300#
Retention cones, module 124" · 150# and 14" · 300#
PSV, fuel gas, drains and spools2"–8" · 150–300#
25 hinstead of 72 h on the retention cones and blinds of one module
47 hearlier module start-up at every maintenance
V-101 24-inch outlet with Superbolt · Abkatún-A
V-101 24-inch outlet with Superbolt · Abkatún-A
Jackbolts, hand wrench
Jackbolts, hand wrench
Working over the side
Working over the side

Zero leaks. Zero re-tightening. Two days back at every start-up.

Example · blowout preventers

The same technology on the drilling rig

The BOP is the last barrier between the well and the crew. Its joints are high-pressure, metal ring-gasket connections, in places where a hydraulic wrench does not fit and nobody wants a hammer wrench.

JointWhat applies
Stack flanges: annular, rams, spools and wellheadSuperbolt · Boltight
Ram bonnets and doorsSuperbolt
Choke and kill lines, choke manifoldSuperbolt
Top drive, mud pumps, drawworksSuperbolt · Nord-Lock washers

Faster nipple-up and nipple-down

Every BOP change is rig time. Several technicians tighten at once with hand wrenches.

Seals first time

Even load on the metal ring gasket, so the pressure test passes without re-tightening.

Safer in the cellar

No hammer wrench, no high-pressure hoses and no heavy gear in a confined space.

Traceable

A torque audit of every tensioner, recorded for the joint file.

Application examples from Nord-Lock Group in oil and gas. BOP manufacturers already use multi-jackbolt tensioners and wedge-locking washers.

Hydril BOP stacks for offshore drilling units, a Nord-Lock Group user
Hydril BOP stacks for offshore drilling units, a Nord-Lock Group user
Nord-Lock Group, Oil & Gas brochure
Nord-Lock Group, Oil & Gas brochure

The last barrier on the rig deserves a known preload.

Turbines

Superbolt on gas and steam turbines

Turbine joints are large, hot and hard to reach. Superbolt loads them evenly without heating the bolts and without impact tools.

  • Casings and horizontal joints. Even tension, no bolt heating, no hammer wrench.
  • Couplings (EzFit). Expansion bolts that go in and come out without seizing. Installed on the Baytown, Texas steam turbine in 2025.
  • Steam valves and piping. Inlet flanges and admission valves.
  • Boiler feed pumps. Tensioners supplied to CFE Carbón II under two contracts, 2022 and 2023.
  • From the factory. The GE D11 and the Siemens 501F ship with Superbolt by design.
Steam turbine inlet flange
Steam turbine inlet flange
Steam turbine split-case joint
Steam turbine split-case joint

Where it goes on a gas turbine

Nord-Lock Group: tensioning solutions for gas turbine frames (with sound)

No bolt heaters. No hammer wrenches. Just a torque wrench.

Wind

Up-tower, where every kilo and every minute counts

A wind turbine is bolted together from the foundation to the blade tips, and most of that work happens in a nacelle with no room for heavy tooling.

JointWhy Superbolt
Main shaft and rotor hubHigh preload in a space where a hydraulic wrench does not fit
Gearbox and generator mountsHolds preload under vibration and load reversals
Blade and yaw bearingsEven load around the full bolt circle
Tower flanges and foundation anchorsLarge diameters tightened with hand tools

Carry a wrench, not a pump

Nothing heavy to lift up the tower.

Pairs with Boltight

For full bolt circles, Typhoon+ hydraulic tensioners are stocked in North America and ship in 48 hours.

Application examples from Nord-Lock Group in wind.

Boltight Typhoon+
Boltight Typhoon+
Superbolt tensioners
Superbolt tensioners
Next

Boltight: hydraulic tensioning, the 4-way joint and casing kits